Parachute dynamics and perturbation analysis of precision airdrop system

To analyze the parachute dynamics and stability characteristics of precision airdrop system,the fluid–structure interaction(FSI) dynamics coupling with the flight trajectory of a parachute–payload system is comprehensively predicted by numerical methods.The inflation behavior of a disk-gap-band parachute is specifically investigated using the arbitrary Lagrangian–Euler(ALE) penalty coupling method.With the available aerodynamic data obtained from the FSI simulation,a nine-degree-of-freedom(9DOF) dynamic model of a parachute–payload system is built and solved to simulate the descent trajectory of the multi-body dynamic system.Finally,a linear five-degree-of-freedom(5DOF) dynamic model is developed,the perturbation characteristics and the motion laws of the parachute and payload under a wind gust are analyzed by the linearization method and verified by a comparison with flight test data.The results of airdrop test demonstrate that our method can be further applied to the guidance and control of precision airdrop systems.     

燃料分级对旋流火焰的动态特性影响研究

为深入研究分级旋流火焰特性,以分级旋流模型燃烧室为研究对象,对四个不同燃料分级比(Rf)条件下的分级旋流火焰进行了数值研究,在时均燃烧场特性分析的基础上进一步对燃料分级比为1和3两个工况进行了基于壁面建模的大涡模拟(WMLES)研究。结果表明:燃料分级比的改变会影响中心回流区(CRZ)的长度和宽度。燃烧室中截面的散点分布图能够显示出不同燃料分级比条件下的燃烧特征。燃料分级比为1时,燃烧室剪切层仅存在零散的涡破碎区;而燃料分级比为3时,伴随涡破碎区还出现了单螺旋分支进动涡核(PVC)。通过FFT变换获得的燃烧室内剪切层速度能谱主频与进动涡核的旋转频率相同,表明内剪切层速度脉动的产生与进动涡核有关。另外进动涡核会使流场内的燃料分布和燃烧模式发生周期性的变化,进而影响燃烧过程。调整燃料分级比在1附近,能够使分级火焰达到稳定燃烧降低排放的目标。     

斜面兜孔圆柱滚子轴承的高速防打滑特性

为解决航空发动机主轴圆柱滚子轴承的打滑问题,提出一种具有斜面兜孔结构的圆柱滚子轴承,并对其高速防打滑特性展开研究。利用Hertz接触理论及弹流润滑、流体动力润滑的经验公式,建立了滚子-内外套圈滚道、兜孔-滚子、保持架-外圈引导面的接触模型。运用多体运动学及牛顿-欧拉动力学理论,建立了轴承径向平面内的三自由度动力学模型,在此基础上,利用龙格库塔数值积分法进行了轴承的动力学数值仿真,探讨了兜孔前后壁倾角对轴承打滑的影响规律,分析了兜孔前壁倾角为5°、后壁倾角为10°下轴承的高速打滑特性,结果表明：兜孔的前后壁倾角对轴承打滑有显著影响,通过对其进行优化,可有效抑制轴承的高速打滑。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian–Eulerian (ALE) approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation. A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished. In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact, a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces. In addition, the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method. Based on this method, fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained. Numerical results such as maximum Root Mean Square (RMS) drag, general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results. This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.     

考虑滑流影响的埋入式进气道气动特性分析与流动控制研究

研究滑流对埋入式进气道性能的影响机理对于发动机的稳定性具有重要意义。针对某型涡桨发动机 滑油散热器进排气道系统,基于 CFD技术建立系统的螺旋桨滑流与滑油散热器内流一体化数值模拟方法,进 行考虑滑流影响的滑油散热系统埋入式进气道气动设计仿真分析;针对埋入式进气道由于吸入边界层低能气 流导致通过散热器流量低的问题,设计4组涡流发生器进行主动流动控制。结果表明:滑流使得进气道中的气 流偏离,难以形成稳定漩涡,容易发生流动分离;而合理设计的涡流发生器可以有效改善埋入式进气道内流场 特性,并使通过散热器的流量提高12%。     

支线飞机替换战略的经济性分析

随着中国城市化进程的发展,西部地区和三四线城市的航空出行需求快速增加。航空公司通常采用干线飞机投入西部航线和三四线城市航空市场,由于客座率不高且航班频次不足,航空公司经济效益不高,西部地区和部分三四线城市的航空出行需求也未得到充分满足。为解决供需矛盾,采用国产某支线飞机替换部分航线经济效益不好的干线飞机虽被提上日程,但是对于替换战略的经济性缺乏定量描述,航空公司始终处于观望状态,进而制约了支线飞机的市场推广。为解决上述问题,构建支线飞机替换战略的经济性模型,随后进行模型验证与仿真分析,比较支线飞机和干线飞机的航段收益,分析所有权模式和关键费用驱动因子对支线飞机运营经济性的影响规律,进而提出支线飞机的优势区域和提升运营经济性的有效措施。     

基于绳系并联机器人支撑系统的SDM动导数试验可行性研究

详细给出了在低速风洞中,采用绳系并联机器人(WDPR)支撑模型,用强迫振荡法进行标准动态模型(SDM)动导数试验可行性的研究。试验中将杆式六分量应变天平内置入模型中以测量模型的气动力和气动力矩,建立了适用于绳系并联机器人支撑系统的模型运动控制子系统和数据采集子系统。采用绳拉力作为参考信号,对气动力矩信号与位姿信号进行数据的同步处理,解决了绳系并联机器人支撑系统应用于动导数试验时所测力矩信号与位姿信号之间的相位差确定问题,给出了WDPR支撑下模型动导数的计算方法。整个试验样机置于某开口式低速直流风洞中进行了俯仰、带偏航角的俯仰以及升沉的动导数试验,通过测量和计算得到各动导数。试验结果与参考文献相比较具有合理的一致性。研究结果表明,采用绳系并联机器人支撑模型进行动导数试验是可行的,至少对于SDM是这样的结果;使用一套绳系并联机器人支撑系统,可以完成多套硬式支撑系统才能完成的动导数试验,从而提高试验效率,降低试验成本。     

Numerical Simulation of Rotor Flow Field Based on Overset Grids and Several Spatial and Temporal Discretization Schemes

A numerical method based on solutions of Euler/Navier-Stokes (N-S) equations is developed for calculating the flow field over a rotor in hover. Jameson central scheme, van Leer flux-vector splitting scheme, advection upwind splitting method (AUSM) scheme, upwind AUSM/van Leer scheme, AUSM+ scheme and AUSMDV scheme are implemented for spatial discretization, and van Albada limiter is also applied. For temporal discretization, both explicit Runge-Kutta method and implicit lower-upper symmetric Gauss-Seidel (LU-SGS) method are attempted. Simultaneously, overset grid technique is adopted. In detail, hole-map method is utilized to identify intergrid boundary points (IGBPs). Furthermore, aimed at identification issue of donor elements, inverse-map method is implemented. Eventually, blade surface pressure distributions derived from numerical simulation are validated compared with experimental data, showing that all the schemes mentioned above have the capability to predict the rotor flow field accurately. At the same time, vorticity contours are illustrated for analysis, and other characteristics are also analyzed.